Bookscanner: Difference between revisions

From Wiki-Fou
(→‎Parts / componentes: Putting the shopping pictures for each component)
(→‎Base / Base: Putting photos)
Line 143: Line 143:


=== Base / Base ===
=== Base / Base ===
[[File:02 BASE 033.JPG|500px|none|left]]
[[File:02 BASE 035.JPG|500px|none|left]]
[[File:02 BASE 040.JPG|500px|none|left]]
[[File:02 BASE 041.JPG|500px|none|left]]
[[File:02 BASE 042.JPG|500px|none|left]]
[[File:02 BASE 043.JPG|500px|none|left]]
[[File:02 BASE 044.JPG|500px|none|left]]
[[File:02 BASE 045.JPG|500px|none|left]]
[[File:02 BASE 049.JPG|500px|none|left]]
[[File:02 BASE 050.JPG|500px|none|left]]
[[File:02 BASE 051.JPG|500px|none|left]]
[[File:02 BASE 056.JPG|500px|none|left]]


=== Column / Columna ===
=== Column / Columna ===

Revision as of 13:16, 25 January 2019

Bookscanning in Calafou:

This page is documenting the design and construction of bookscanners. For the tutorial that explains "How to use the bookscanner", go to http://wiki.calafou.org/index.php/Bookscanning

Building a "New Standard Scanner"

We built this: https://forum.diybookscanner.org/viewtopic.php?f=1&t=333 during the Kunlabora event in Calafou: https://calafou.org/en/content/kunlabora-ephimeral-projects-kooperative A more reproducible and portable and simple scanner.

In theory for the simple scanner it should be possible to get all the ingredients from a hardware shop ("ferreteria"). We got most of the materials from Bauhaus in Barcelona (Zona Franca). Our experience was that most of the screws, nuts and bolts are easy to substitute with others that have more or less the same dimensions.

Bookscanner pseudoready2.jpg

Budget

Kunlabora event was four days of collaborative construction. More or less six persons worked on building the scanner. This is the receipts that we spent, because we had 500 EUR budget for the raw materials from the participation fee of the event.

Receipts:

   25    2x plexiglass [J] @ Expocryl, Igualada
   18    2x SD cards @ Life Informatica, Barcelona
   50    2x magic want camera stand @ FotoK, Barcelona
   42.2  Nuts/bolts/etc. @ Bauhaus, Zona Franca, Barcelona
   108.8 Nuts/bolts/etc. @ Bauhaus, Zona Franca, Barcelona
   10    2x USB cable male/female @ Worten San Antoni, Barcelona
   5     2x mini USB (USB-B) cable @ Tienda Cables, Barcelona
   178   2x Canon IXUS 175 compact digital camera @ Amazon.es
   60    4x Wooden beams (listones) @ Fustes Fargas, Barcelona
   ============================================
   497

Donations:

   70    Raspberry Pi 3 (Model B), 2x SD cards, 5V charger, rulers [M] @ Barcelona

We also used nuts and bolts, etc. found in the workshop of Calafou (in Catalunya, near Barcelona). The conclusion is that it should be possible to build this scanner from about 5-600 EUR anywhere in (Western) Europe. We did not use all the materials we bought and if we would do it again then we tried to use real wood instead of FDM, because the latter proved very fragile. However, this could make the platen more heavy, and it is already quite heavy.

Parts / componentes

01 SHOPPING 001.JPG

Going for shopping

Error creating thumbnail: File missing


From Bauhaus, Barcelona (Zona Franca):

01 SHOPPING 027.JPG
-1x Varilla roscada
-4x Listones de madera  ~800x40x90mm
-2x (Tablero) MD sheet 600x400x10mm
-2x (Tablero) MDF sheet 600x400x16mm
Error creating thumbnail: File missing
- Cola blanca rápida para madera
Error creating thumbnail: File missing
- Base 4 tomas 1.5 mts
01 SHOPPING 007.JPG
- Tuerca hexagonal
01 SHOPPING 020.JPG
- Guia corredera
01 SHOPPING 004.JPG
- Arandelas ancha
01 SHOPPING 005.JPG
- Aldabon BPF 185 M
01 SHOPPING 006.JPG
- Tornillo mad.cab.pl.
Error creating thumbnail: File missing
- Tornillo cab. avell.
01 SHOPPING 011.JPG
- Tornillo p/metal
01 SHOPPING 008.JPG
- Tuerca palomilla
01 SHOPPING 021.JPG
- Guia cajones 10kg
01 SHOPPING 022.JPG
- Spax cab. red zinc
01 SHOPPING 012.JPG
- Tirador dorado
01 SHOPPING 014.JPG
- 4x Abrazaderas
01 SHOPPING 025.JPG
- Mosqueton-fw
- 2 x plexi glass 380x280x3mm from a company in Igualada that J. found.

Other things from other shops:

01 SHOPPING 013.JPG
- 4x Cable USB 2.0 male-female @ Worten Sant Antoni
- 2x USB-A -> USB-B (mini) cables @ Tienda de Cables
- 2x SD Cards 16 Gg
Error creating thumbnail: File missing
- 2x Manfrotto brazo flexible MF237 (Nr. referencia AFP018036) @ FotoK, Ronda Universitat
01 SHOPPING 015.JPG
- 2x Tira LED 1 nice
- 2 x digital cameras (see below for background information): Canon IXUS 175 (Powershot / ELPH 180)
  - https://www.amazon.es/Canon-IXUS-175-compacta-estabilizador/dp/B01A8QU70I/
  - http://chdk.wikia.com/wiki/ELPH180
  - https://www.canon-europe.com/for_home/product_finder/cameras/digital_camera/ixus/ixus_175/specification.aspx

For electronic parts a good shop in Barcelona is Diotronic: https://diotronic.com/

- usb charger to give power to the external trigger trough USB cable

Things to take in consideration from the building experience

  • the MDF pieces are fragile and gave us problems when introducing screws
  • we considered varnishing the wood pieces to limit humidity impact
  • the plexiglas we bought generates many reflections
  • passing from inches to cm was uncomfortable
  • the position and height of the light should be tested before being fixed
  • the upper part of the light stand should be easier to mount and unmount for transportation
  • the wood used for the platen should be without texture or painted with mate dark paint
  • the gooseneck (Manfrotto) option for the camera stand is not a good option: it is very easy to put the camera in the way of the cradle; the calibration process is difficult because the cameras can move in the three axis; they are springy and difficult to set in an exact position

Cameras

The bookscanner is basically a glorified camera stand that allows us to take good pictures of book pages. So the cameras are an important part of the bookscanner. Summary of research about cameras for book scanners:

Basically there are three categories of cameras that can be used for book scanners (from cheapest to most expensive).

1. Remote control support

The cheapest option is any camera with remote trigger support, so we can take pictures without pushing the button on the camera. This is important because when you press the button the camera position may be disadjusted to the physical pressure.

2. CHDK firmware

Middle category is CHDK firmware compatibles. CHDK is a third party open source firmware that allows the customisation of cameras. CHDK firmware is for Canon Powershot cameras, which are the cheaper compact digital camera product line. We have 200 euros in the budget for cameras, so we went with this option.

3. Magic Lantern support

Magic Lantern is a third party open source firmware that is more advanced. However, it only works with Canon DLSR cameras (these are the cameras that have a reflex mirror to look at the shot through a small hole before you take the picture, and they usually have big lenses). The scanner we have now uses Canon 1100D, which are the cheapest type suported by Magic Lantern, but they still cost a few hundred euros.

4. Connecting to a monitor

It is very useful to be able to connect the cameras to a monitor during the calibration process. The cameras we bought use the same output for connecting to a remote control and to a monitor making it not practical at all using a monitor. Furthermore, connection with usb to a computer monitor was not an option, we had to look for RC connectors or adapters.

Building process

Base / Base

02 BASE 033.JPG
02 BASE 035.JPG
02 BASE 040.JPG
02 BASE 041.JPG
Error creating thumbnail: File missing
02 BASE 043.JPG
02 BASE 044.JPG
02 BASE 045.JPG
Error creating thumbnail: File missing
Error creating thumbnail: File missing
02 BASE 051.JPG
02 BASE 056.JPG

Column / Columna

Cradle / Cuna

Platen / Platina

CHDK

Photos

Shopping

Base

Cradle

Platen

Column

Mounting

Miscellaneous

Triggering mechanism

Camera holder

Day 1 (temporary)

Raspberry Pi for the bookscanner

At the moment we use an electromechanical button documented on the CHDK website that works well but does not do much more than triggering the two cameras to shoot at the same time: http://chdk.wikia.com/wiki/USB_Remote

There are many more possibilities of how to optimise the bookscanning process. Many ideas start with connecting the cameras to a small computer such as the Raspberry Pi. We made some experiments and tests with this setup, which is documented below:

It runs Raspbian.

CHDKPTP

In /home/pi/chdkptp there are precompiled binaries of CHDKPTP downloaded from here.

CHDKPTP is used for remote control of camera running CHDK firmware.

Our setup has two modes of work:

  • mechanical "button" which triggers both camera capturing its photo based on this tutorial: http://chdk.wikia.com/wiki/USB_Remote
  • (in progress) Raspberry Pi mode where an bookscanner operator uses Raspberry Pi to capture photos, preview photos in real time and transfer them already renamed for the next step in Scantailor.

When camera is connected this line will list info about the camera e.g.:

sudo ./chdkptp.sh -elist

and for one of the camera this is what is listed then:

-1:Canon IXUS 175 b=001 d=030 v=0x4a9 p=0x32c1 s=8B20D62641B041BAA3E1D597D560D110

An example of capturing a picture from commandline (once in /home/pi/chdkptp/):

sudo ./chdkptp.sh -e"connect -d=030" -erec -eshoot

Above line connects to the camera sitting on -d=021, puts it into rec mode (if not already) and capture the photo saving it to SD card already in camera. If one wants to bypass the SD card altogether it should replace -eshoot with -eremoteshoot. In that case ./chdkptp.sh will save photos into the directory from where it was called.

Note: check the SD card is locked.

ZeroTier

It is added to 565799d8f6ebf1a8 public network of ZeroTier with this command:

sudo zerotier-cli join 565799d8f6ebf1a8

and it got static IP address (in 565799d8f6ebf1a8 network):

192.168.192.171/24

In /home/pi/.ssh/authorized_keys public keys of maxigas and marcell are added.

Ideas for building Voja's scanner

Our first idea was to reproduce Voja's scanner but we had to realise that we are not Voja and the scanner is very beautiful and unique engineering and consequently it is hard to reproduce.

Here are two links to the public documentation of our scanner, built by Voja Antonic:

https://www.memoryoftheworld.org/blog/2012/10/28/our-beloved-bookscanner-2/

https://hackaday.io/project/5604-diy-book-scanner

The electronics is not really documented (which means that it is hard to reproduce) and it is built from basic parts (which means that it takes a lot of time to put it together). So we brainstorm about an Arduino-based solution instead. Arduino is a general-purpose programmable microcontroller that has already built-in many of the functions/parts we need. The idea is that this makes it easier for us to build the scanner and for others to reproduce it. We also have more experience working with Arduino than with only basic electronic components.

We will also try to use cheaper cameras in order to bring down the budget.

Biblio-graphy

About our first bookscanner

English

Spanish

Principal sources

Reading And Leading With One Laptop Per Child

Future activities

next steps